Département Électromécanique
Permanent URI for this collection
Browse
Browsing Département Électromécanique by Title
Now showing 1 - 20 of 69
Results Per Page
Sort Options
Item Adaptation d'un système pour relier deux chaine Cas : l’entreprise nationale l’ENIEM.(Université Mouloud Mammeri Tizi Ouzou, 2022-09) Adda, Abderrazak; Cherki, MouradNotre projet de fin d’étude est effectué en grande partie au sein de l’Entreprise Nationale des Industries de l’Electroménagers ENIEM dans le but d’implanter une solution pour le robot de transfert. en utilisant le système de convoyeur avec la logique câblée programmable. Ce stage de fin de cycle nous a été bénéfique à plusieurs titres : La découverte et l'apprentissage des plusieurs domaines d'études tels que la réalisation des circuits électriques, assemblage de différentes pièces mécaniques.... Et nous avons renforcer nos connaissances théoriques par une expérience pratique non négligeable dans le domaine de l'électromécanique. Nous avons présenté les composants électrique de l'armoire qui construit une logique câblée pour mener le robot et les convoyeurs à une bonne action. Puis nous avons présenté le robot on décrierons particulièrement ses différentes étapes de fonctionnement. Et nous avons terminé par donné une proposition au problème posé. Nous souhaitons que notre objectif a été atteint vu qu’on a respecté l’intégralité du cahier de charges. Nous espérons que notre travail verra naître sa concrétisation sur le plan pratique et que les promotions à venir puissent en tirer profit.Item Application de la méthode SVM à la détection et la classification des défauts dans les machines tournantes(Université Mouloud Mammeri Tizi Ouzou, 2021-06) Larabi, Hamimi; Ahcene, SidaliCe mémoire présente une technique de diagnostic de défaut et de classification basée sur la méthode d'apprentissage automatique « Les Machines à Vecteurs de Support, SVM » qui est basée sur des données. Dans notre travail, nous nous intéressons à la classification des défauts de roulement apparaissant dans les machines tournantes avec la méthode SVM. Dans la phase de classification, les machines à vecteurs supports (Support Vector Machines (SVM)) ont été retenues. Ce système de diagnostic a été évalué en utilisant des signaux vibratoires en différents modes de fonctionnement (sain et avec défauts). Les résultats obtenus montrent l’efficacité de cette approche.Item Application de l’analyse AMDEC sur un système de graissage des glissières des machines-outils(Université Mouloud Mammeri, 2023) Gada, Lyes; Hamouche, MokraneLa maintenance est un élément très important et essentielle pour assurer la disponibilité, la fiabilité et la performance des équipements et des installations d'une entreprise. L'AMDEC (Analyse des Modes de Défaillance, de leurs Effets et de leur Criticité) est une méthode d'analyse et de prévention des défaillances qui vise à identifier les modes de défaillance potentiels, évaluer leurs conséquences. Elle contribue ainsi à améliorer la fiabilité, la sécurité, la qualité et la satisfaction client. Les machines-outils sont des équipements mécaniques utilisés pour façonner les matériaux en pièces finies qui se composent de plusieurs éléments statiques et dynamique. Ces derniers sont responsables de la transformation de l'énergie en mouvement, parmi ces organes dynamiques on trouve les glissières ; qui sont des rails ou des guides qui maintiennent le mouvement de la pièce et/ou de l'outil dans une direction précise, qui ont le rôle d’éliminer au chariot cinq degrés de liberté d’une manière qui permets un déplacement unidirectionnel en général linéaire.Item Application des outils de Méthodes de maintenance sur le moteur Caterpillar 3512(Université Mouloud Mammeri, 2023) Ben Chabane Raouia; Aggar NaimaLe moteur Caterpillar 3512 est un moteur diesel Il est considéré comme le coeur de la source de l’énergie électrique Il entraîne un alternateur pour produire de l’énergie électrique afin d’alimenter les équipements de forage. Sa conception robuste, sa puissance élevée et sa capacité à fonctionner dans des conditions difficiles en font un choix populaire dans l'industrie. Nous avons cité certaines pannes du moteur afin d’appliquer les nouvelles méthodes de maintenance comme la méthode AMDEC ou on trouve les modes de défaillance et comment les répares, et la méthode d’ISHIKAWA qui aide à savoir toutes les causes possibles d’une panne et nous avons dessiné la courbe ABC pour identifier les pannes critiques nécessitant plus de temps pour être corrigées.Item Automatisation de la centrale à béton PowerMix90 via Tia Portal V13.(Université Mouloud Mammeri, 2023) Bachir Amar; Arbane MakhloufCe projet de fin d'études vise à reprogrammer l'automate qui contrôle une centrale à béton, dans le but d'améliorer son fonctionnement et d'assurer la sécurité du personnel. Commencent par une exploration des informations générales sur les centrales à béton, notamment leur structure, les étapes de fabrication du béton, et les différents types de centrales disponibles. Ensuite, l'accent est mis sur la programmation de la centrale, avec le développement de deux modes de fonctionnement : un mode manuel et un mode automatique, en utilisant le logiciel TIA PORTAL V13.Item Automatisation et supervision de la centrale à béton ELBA, avec Automate S7 1200 programmé via Tia Portal V13(Université Mouloud Mammeri Tizi Ouzou, 2022) Hasbellaoui, Ahmed; Harikenchikh, FatehAu cours de ce travail, nous avons pu reprogrammer l’automate commandant la centrale à béton sur laquelle porte l’étude en réalisant une tout autre conception pour celui-ci et en optant pour une solution améliorant le fonctionnement et la productivité de la centrale, mais également répondant aux normes de sécurité afin de protéger au mieux le personnel sur le chantier. Grace à l’outil de modélisation du fonctionnement « GRAFCET », nous avons établi une architecture globale du programme propre et adaptée au fonctionnement de la machine et aux besoins de la société. Sur base de cette ossature ensuite, c’est construite la réflexion sur la recherche de solutions logiciel au fonctionnement des différentes parties de la machine pour garantir sa concordance avec les exigences du cahier des charges ainsi qu’avec les besoins de la société. L’automate choisi étant de marque Siemens, la programmation c’est évidement faite sur le logiciel de cette même marque, en l’occurrence Tia Portal V13. Avec une interface assez intuitive, les fonctions intégrées et conçus pour l’automatisation de processus industriels, nous avons pu, en utilisant le langage Ladder, élaborer un programme complet pouvant faire fonctionner la machine en mode automatique, pour une fabrication autonome et sans surveillance de grandes quantités de bêton, mais également, un mode manuel a été prévu pour un fonctionnement à vue et commandé par un opérateur qualifié. Pour se faire, nous avons également proposé une interface de supervision, à travers un écran Siemens KTP 1200 pour le contrôle et la surveillance du processus à travers une visualisation claire, simple et intuitive. L’écran renvoie un visuel du processus en cours, indique les différentes parties mises en marche de sorte que d’un simple coup d’oeil sur l’écran, l’ouvrier aura toutes les informations pertinentes sur le travail en cours, mais également, en cas de déclenchement, des informations sur les alarmes et leur provenance. A travers ce même écran et sur un menu différent, il est possible d’avoir plusieurs recette ou formules de béton enregistrées et réalisables par un simple clic sur un bouton. Ces recettes peuvent être modifiées à volonté. L’automatisme et les API sont donc des moyens forts efficaces, proposant des outils avec de larges bibliothèques de fonctions et de possibilités répondant à la quasi-totalité des besoins en industrie, ce qui nous a ainsi permis d’accomplir ce travail.Item Conception d'une application de gestion de la maintenace assistee par ordinateur(Université Mouloud Mammeri, 2023) Azzoug Yahia; Hadjer RayanCe travail met en évidence l'évolution de la gestion de la maintenance, initialement négligée pour sa complexité, mais désormais soutenue par l'informatisation grâce à l'émergence des GMAO. Cette informatisation offre des avantages considérables, tels que des outils de calcul puissants, un stockage de données robuste et une traçabilité accrue. L'objectif du projet était de créer un logiciel intégrant les principes de la gestion de la maintenance, fournissant des estimations précises basées sur les données historiques. La plateforme est conçue pour être conviviale, mais des améliorations futures sont envisagées, notamment des fonctionnalités avancées, des calculs statistiques prévisionnels et une aide à la prise de décision basée sur les archives.Item Conception d'une application de gestion de la maintenace assistee par ordinateur(Université Mouloud Mammeri, 2023) Azzoug Yahia; Hadjer RayanCe travail met en évidence l'évolution de la gestion de la maintenance, initialement négligée pour sa complexité, mais désormais soutenue par l'informatisation grâce à l'émergence des GMAO. Cette informatisation offre des avantages considérables, tels que des outils de calcul puissants, un stockage de données robuste et une traçabilité accrue. L'objectif du projet était de créer un logiciel intégrant les principes de la gestion de la maintenance, fournissant des estimations précises basées sur les données historiques. La plateforme est conçue pour être conviviale, mais des améliorations futures sont envisagées, notamment des fonctionnalités avancées, des calculs statistiques prévisionnels et une aide à la prise de décision basée sur les archives.Item Conception d’un Concentrateur d’oxygène médicale(Université Mouloud Mammeri Tizi Ouzou, 2022-07) Aliouane, Yacine; Maredj, AbderrahmaneSuite a la catastrophe covid-19 pandémie mondial, maladie contagieuse qui a cause beaucoup de perte humaine et la catastrophe naturelle qu’a subit notre pays, le feu qui a rase nos terres, qu’a cause ainsi des pertes humaines et matériels. L’autonomie en oxygène des hôpitaux qui reste soumise a la production des laboratoires pharmaceutique, a été très vite dépassée dans cette pandémie de maladie avec atteinte respiratoire. Le recours aux concentrateurs d’oxygènes pour la production d’oxygène conforme à la pharmacopée européenne oxygène 93 intéresse les établissements hospitaliers pour une utilisation régulière sur leurs réseaux d’oxygène. La production d’oxygène par les concentrateurs parait la plus économique, tout en offrant le maximum d’autonomie en situation d’exception. La réalisation de ce concentrateur d’oxygène qui pourra produire 30 L/Min vas assurer la disponibilité de ce Gas indispensable a la vie et à la survie. Enfin, le concentrateur que nous avons conclu, peut satisfaire les besoins des hôpitaux et clinique qui ne sont pas doté de station de production d’oxygène, quelques concentrateurs avec ces performances peuvent remplacer une station de production au niveau d’un hôpital ou une clinique, ce qui est très favorable financièrement parlant, car le cout d’un concentrateur est trop faible par rapport a une station.Item Conception d’un GRAFCET et application de la méthode de maintenance AMDEC de la machine Battage Polyester au niveau de l’EATIT de DRAA BEN KHEDDA.(Université Mouloud Mammeri Tizi Ouzou, 2022-07) Cherifi, LyesArrivant à la fin de notre projet de fin d’études portant sur conception d’un GRAFCET et de Maintenance de la machine Battage Polyester, nous présentons le bilan du travail que nous avons effectué. Il a fallut bien s’intégrer et comprendre le fonctionnement de la machine. D’abord nous avons modélisés le système de la machine par GRAFCET pour décrire graphiquement les différents comportements de la machine. La défaillance de la machine ne peut pas échouer, mais peut être contrôlée par une maintenance bien organisée, qui améliore les conditions de travail et minimise le coût de réparation puisque elle reste la machine toujours en marche et éviter l’arrêt complet des machines. Pour que ces objectifs soient atteints nous avons utilisés la méthode AMDEC machine qui est un outil d’analyse très performent contribuant à la détermination des différents points critiques de la machine et qui permet de déterminer les actions adéquates à engager dans le but d’augmenter la fiabilité et la disponibilité du système étudié. En conclusion, ce travail présente un grand intérêt pour nous puisqu’il s’agit d’un travail purement industriel qui nous a permis d’avoir une vision claire sur le GRAFCET et la méthode de maintenance AMDEC en phase de production et d’exploitation.Item Conception d’un logiciel de GMAO(Université Mouloud Mammeri Tizi Ouzou, 2022-09) Benali, Madjid; Hassad, DjamalCe présent travail a pour objectif la réalisation d’un logiciel de gestion de la maintenance. Pour cela nous sommes passés par une recherche et étude bibliographique, détaillée dans ce mémoire, traitant des différents types et outils de la maintenance au sein de l’industrie, cela afin de synthétiser les opérations essentielles que doit effectuer le système, qui y seront intégrées comme fonctionnalités. Après l’étude, nous avons ensuite fait appel au logiciel Matlab, via « appdesigner » pour créer la plateforme graphique ainsi que l’intégration des différentes fonctions de calcul du logiciel.Item Conception d’un moteur asynchrone monophasé(Université Mouloud Mammeri Tizi Ouzou, 2022-09) Bouzaria, Samy; Ouikene, ArezkiLe moteur asynchrone a cage d’écureuil est le plus répandu dans l’industrie. En raison de sa simplicité, sa robustesse, son cout modéré et sa fiabilité. Les moteurs asynchrones triphasés présentent du point de vue technico-économique, des avantages par rapport aux moteurs asynchrones monophasés lesquels manifestent des difficultés au démarrage, afin d’y remédier, des moteurs asynchrones monophasés à enroulement auxiliaire ont été conçus, en particulier ceux condensateur permanent qui fera l’objet de notre étude. Ces derniers trouvent une large application dans les appareils électrodomestiques : machines à laver, réfrigérateurs.Item Conception et fabrication d'un e-kart(Université Mouloud Mammeri Tizi Ouzou, 2021-07) Ould Amara, Nabil; Si Salah, Mohamed SalimUn kart est un petit véhicule à quatre roues spécifiquement conçu pour être utilisé sur les pistes, il est généralement utilisé pour apprendre à conduire dans un environnement sans danger. Ce projet vise à simuler, réaliser l'analyse statique et dynamique et à fabriquer un E-Kart qui soit solide, léger et durable. Les simulations sont réalisées à l'aide d'un logiciel de CFAO, à savoir SOLIDWORKS et ANSYS. La déflexion maximale est déterminée en effectuant une analyse statique pour s’assurer de la solidité du châssis. Le châssis est conçu de telle sorte qu'il nécessite moins de matériaux et qu'il soit suffisamment solide pour résister aux différents impacts qu'il subit. La solidité et la légèreté ont été notre principal critère lors de la conception du châssis du E-kart. Par conséquent, l'AISI1010 a été sélectionné comme matériau approprié pour la conception. La fabrication du châssis a été effectuée en suivant le modèle 3D réalisé après avoir fait toutes les simulations et les études nécessaires. Pour la motorisation et la commande du E-Kart, nous avons utilisé les programmes ISIS PROTEUS et Micro C puis nous avons opté pour l’utilisation d’un microcontrôleur ATMEGA328 et un ESC pour pouvoir commander le moteur avec la PWM.Item Conception et réalisation d'un drone quadri-rotor personnalisé(Université Mouloud Mammeri Tizi Ouzou, 2022-07) Ouacel, SaidLes drones quadri-rotor sont des robots volants faisant partie de la famille des multi rotors qui peuvent mener à bien une mission de manière autonome ou téléguidée. Le travail présenté dans ce mémoire est l’étude et la réalisation d’un drone quadri-rotor personnalisé. Notre quadri-rotor est réalisé à partir de quatre moteurs sans balais BLDC. Ces moteurs sont commandés depuis un circuit appelé contrôleur de vol, son emplacement est au centre du quadri- rotor, ce circuit permet de gérer les BLDC en utilisant des contrôleurs de vitesse électronique (ESC), l’ensemble est alimenté par une carte de distribution PDB qui est alimentée par une batterie Li-PO et piloté par une radiocommande dotée d’un émetteur et d’un récepteur. La stabilisation du drone a été assurée en implémentant une loi de commande de type PID. La personnalisation de notre drone quadri-rotor s’est effectuée au niveau du châssis qui est conçu de telle sorte qu'il nécessite moins de matériaux et qu'il soit suffisamment solide pour résister à la charge et qu’il soit équipé d’un panier. La solidité et la légèreté ont été notre principal critère lors de la conception du châssis personnalisé du drone quadri-rotor. Par conséquent, le PPR a été sélectionné comme matériau approprié pour la conception. La réalisation du châssis a été effectuée en suivant le modèle 2D réalisé par nos soins. La configuration de notre contrôleur de vol s’est effectuée à partir d’un logiciel Cleanflight Configurator.Item Conception et réalisation d’un smart robot Arduino télécommandé détection des flammes et des objets(Université Mouloud Mammeri Tizi Ouzou, 2021-06) Sam, IbtissemL’objectif de ce projet est de concevoir et de réaliser une commande à distance pour un robot mobile à chenille, à l’aide d’une carte Arduino Uno .le but est que le robot puisse se déplacer dans un environnement statique et d’indique la température et de pouvoir visualiser les terrains pour l’observateur, cette machine est dotée de fonctions de perception, de décision et d’action afin d’être capable d’effectuer des taches diverses et d’accomplir correctement sa tache. En autre nous proposons une application Android pour pouvoir choisir le mode de contrôle du robot.Item Conception et réalisation d’une ruche d’abeille isotherme en plastique(Université Mouloud Mammeri, 2023) Tararbit Anis; Sadi SaidDans ce mémoire, nous explorons en profondeur le domaine de l'apiculture avec un accent particulier sur la conception et l'étude de la ruche d'abeille en plastique. Dans le chapitre introductif, nous contextualisons notre travail en présentant l'histoire de l'apiculture, son importance économique et écologique, ainsi que les ressources florales et la répartition géographique des abeilles. Nous abordons également les aspects commerciaux. Dans le deuxième chapitre, nous effectuons une étude comparative approfondie des différentes typologies de ruches, en examinant des critères techniques tels que les matériaux de conception, les dimensions, la durée de vie, la capacité, la facilité de montage/démontage, la résistance aux conditions météorologiques et les risques associés. Le chapitre trois se concentre sur le dimensionnement de la ruche moderne, en analysant les matériaux utilisés, les composantes clés et les processus de fabrication. Enfin, dans le quatrième chapitre, nous menons une analyse technico-économique en évaluant les coûts de fabrication, l'impact sur le marché apicole algérien, et la satisfaction des éleveurs. Cette recherche vise à fournir une compréhension approfondie de la ruche d'abeille en plastique et à contribuer aux avancées dans le domaine de l'apiculture. (ruche, moule en plastique, plastique, polyéthylène (PE), Polypropylène (PP), polyuréthane (PU), polystyrène expansé, moteur électrique, carte électronique, capteur d’humidité).Item Contribution à l’identification d’endommagement des structures plaques par des méthodes d’analyse dynamique et les algorithmes d’optimisations.(Université Mouloud Mammeri Tizi Ouzou, 2021) Keddam, Yanis; Oulmane, Mohand-SaidLe travail présenté dans ce mémoire a pour objectif la détection d’endommagement dans les structures plaque par techniques vibratoires, nous avons opté pour la méthode de l’énergie de déformation en exploitant la fonction de réponse fréquentiel pour la localisation de l’endommagement, et enfin utiliser deux algorithmes d’optimisations a de fin comparatif et pour la quantification de la sévérité de l’endommagement. En effectuant une étude comparative entre les fréquences saines et endommagés nous avant pu détecter la présence d’un endommagement. Ensuite, nous avons procédé à la localisation des endommagements dans deux (02) structures plaques distinctes, une plaque (64 éléments) avec les conditions limite « CCCC » et une autre avec le même nombre d’élément mais cette fois si avec d’autre condition limite « SCSC », pour trois scénarios d’endommagements en utilisant la méthode de détection des endommagements basé l’énergie de déformation en exploitant la fonction de la réponse fréquentielle. La représentation graphique de l’indicateur MSEI FRF utilisé nous a permis de localisé avec exactitude les éléments endommagés qu’on a mis dans la simulation. Après l’étape de la localisation, nous avons cherché à quantifier la sévérité des endommagements en utilisant deux algorithmes d’optimisation, à savoir : l’algorithme (BWOA) et (JSOA), Et effectuer une étude comparative entre ces deux algorithmes. Afin de pouvoir comparer ces deux méthodes nous avons présenté les résultats sous formes de tableaux et graphiques, l’analyse et la lecture faite de ses derniers sont basés sur ces paramètres à savoir : BEST qui est le taux d’endommagement, Fitness qui représente la convergence des taux du taux d’endommagement. La vitesse de convergence (fitness) ainsi que le taux d’endommagement (BEST), nous ont montré tout au long des simulations, que l’algorithme JSOA est plus performant, sa convergence est plus rapide, et le taux d’endommagement obtenu est plus précis. On a également constaté, les calculs sont plus précis. Et c’est ainsi d’après les résultats qu’on déduit que la méthode JSOA est plus fiable que la méthode BWOA. En variant les itérations entre (100 et 200) et les populations entre (100 et 200) on a pu constater qu’avec des valeurs supérieures d’itérations on obtient des valeurs fitness plus basse et aussi une vitesse de convergence plus importante par rapport à celle obtenue avec l’augmentation des valeurs de populations et la réduction des itérations. Conclusion générale 94 En somme, bien que l’algorithme JSOA est plus performant que BWOA, les résultats donnés par ces derniers sont assez satisfaisant pour quantifier les endommagements.Item Contribution au diagnostic des défauts à l’aide des réseaux neurones artificiels RNA. Cas : Défaut de température d’huile de la turbine à vapeur(Université Mouloud Mammeri Tizi Ouzou, 2021-09) Hammoum, aghilas; Arezki, JubaLe travail présenté dans ce mémoire porte sur l’étude des réseaux de neurones artificiels pour la surveillance et diagnostic d’un défaut d’augmentation de la température d’huile dans les sorties des paliers d’une turbine à vapeur au niveau de la centrale thermique de Cap Djinet au sein de l’entreprise SONALGAZ. Dans un premier temps, nous avons entamé notre travail par la présentation de la centrale thermique de cap Djinet et son fonctionnement technologique. Puis nous avons présenté notre système étudié à savoir le système d’huile de la turbine. Nous avons par la suite présenté les principaux défauts des machines tournantes et la technique de réseau de neurones artificiels RNA En dernier lieu, Nous avons élaboré un programme de surveillance pour le défaut de température d’huile dans les sorties des paliers de la turbine. Pour ce faire, nous avons proposé la technique de réseau de neurones artificiels multicouches PMC pour la surveillance des défauts. Une fois que l’apprentissage du réseau est terminé et devenu prêt, nous l’avons testé en changeant les valeurs des températures d’huile au niveau des sorties des paliers de la turbine. Les résultats ont montré que le réseau de neurones artificiel était à la hauteur avec une erreur quadratique négligeable. En perspective, il est intéressant : ➢ De faire une étude comparative entre la méthode des réseaux de neurones artificiels en utilisant l’algorithme de Perceptron Multi Couches (PMC) avec la méthode de surveillance avec modèle en utilisant la technique d’automatique, en termes d’efficacité. ➢ D’étendre l’étude pour d’autre types et architectures de réseaux de neurones, entre autres les réseaux feed-forward avec rétroaction (feed-back). ➢ D’étendre l’étude pour d’autres types des défauts de la turbine à vapeur, tels que défaut de vibrations d’un roulement et le déséquilibre massique des rotors. Enfin, nous espérons que l’étude effectuée présente un intérêt pour l’entreprise, et apporte un éclairage aux étudiants qui auront à préparer leur projet de fin d’études ultérieurement.Item Détection des défauts dans les structures mécanique par la méthode de collocation isogéometrique.(Université Mouloud Mammeri TiziOuzou, 2020-07) Abdennour, Massinissa; Moulai, KhaledCe mémoire vise, dans un premier temps, l’étude de la méthode de collocation isogéometrique en tant qu’outil de modélisation des endommagements dans les structures mécaniques et dans un second temps, la conception d’une application de détection des endommagements est réalisée et cela en implémentant l’algorithme développé sous matlab. Les résultats obtenus sont ensuite validés par comparaison aux données issues de publications scientifiques récentes. Les outils nécessaires pour le traitement de la problématique sont présentés et étudiés dans les quatre premiers chapitres comme suit : Le premier chapitre traite la modélisation géométrique par les fonctions B-Splines et NURBS. Dans ce chapitre, nous avons tout d’abord présenté les fonctions de base, les courbes ainsi que les surfaces B-Spline polynomiales. Ensuite, nous avons présenté les fonctions de base B-spline rationnelles non uniformes (NURBS) suivi de plusieurs exemples de courbes et surfaces. Le but de cette partie du travail est de maitriser les modèles précédemment cités en vue de les utiliser comme fonctions de forme pour la méthode de collocation isogéometrique. La base NURBS s’avère être le modèle le plus performant pour la représentation des géométries complexes. Ce qui fais de lui, le meilleur candidat pour la représentation des champs de solution d’équations aux dérivées partielles en tant que fonction de forme. Dans Le deuxième chapitre, nous avons étudié les fondamentaux des méthodes de collocation ‘ méthodes pseudo-spectrales’. Nous avons présenté tout d'abord les bases théoriques des méthodes de collocation. Par la suite, nous avons présenté la méthode de collocation isogéométrique qui est utilisée dans la modélisation du comportement dynamique des structures mécaniques. Dans le troisième chapitre, nous avons étudié la modélisation analytique des éléments de structures mécaniques en dynamique, plus précisément de la poutre de Timoshenko. Ce chapitre traite le développement d’un problème aux valeurs propres à base de l’équation de Timoshenko en vue de calculer les fréquences et les modes de résonance la poutre. Dans le quatrième chapitre, nous développons le modèle numérique du problème aux valeurs propres. Nous présentons par ailleurs la méthode d’injection des conditions aux limites tirées de la référence [13]. Dans le cinquième chapitre, nous présentons un l’algorithme de détection des défauts par le vecteur des forces modales résiduelles, celui-ci, nous permet d’identifier et de localiser des endommagements. Cette méthode est principalement basée sur les variations des modes propres induits par l’endommagement. Chaque application est accompagnée de résultats et explications : Un test de validation est effectué, celui-ci consiste à calculer les fréquences et les modes propres d’une poutre saine (sans endommagements). Les paramètres géométriques, matériaux ainsi que les conditions aux limites ont été choisi de manière à se conformer aux publications dans le domaine afin de permettre la comparaison. Le premier test nous a permis de valider le modèle numérique construit. Le second test consiste à appliquer un endommagement progressif à une poutre et à observer l’évolution des fréquences de résonance de celle-ci. La méthode de modélisation de l’endommagement est tirée de la référence [9] celle-ci consiste à soumettre l’équation du mouvement à une fonction de distribution des raideurs ; un endommagement se manifeste par une diminution de la raideur à proximité de sa zone. Les résultats sont en bon accord avec ceux de publications scientifiques récentes. le dernier chapitre est dédié à l’application des résultats obtenus par un algorithme de détection et de localisation des endommagements par la méthode des forces modales résiduelles. Les résultats sont présentés sous forme graphique et comparés à ceux publiés. La méthode de collocation isogéométrique présente bien des avantages. Elle permet notamment de modéliser des formes géométriques complexes, de briser les barrières entre les logiciels de CAO et de simulation numérique par l’utilisation d’un même modèle géométrique. Cela permet d’économiser environ 80% du temps de calcul (voir la réf [5]), d’éliminer l’erreur d’interpolation de la géométrie et d’assurer la convergence. La IGA-C offre une possibilité de raffinage par insertion de noeuds et/ou d’élévation de l’ordre d’approximation indépendamment. Par ailleurs, elle offre la possibilité de contrôler la continuité de la solution par multiplication des noeuds. Bien que cette méthode présente des avantages importants, elle reste tout de même complexe à appréhender. Par ailleurs, la IGA-C reste au stade de développement. A ce jour peu de logiciels de simulation numérique l’utilisent. Notre projet de fin d’études nous a offert l’opportunité de maitriser la modélisation et la dynamique des structures mécaniques et de nous initier à l’utilisation des méthodes numériques Conclusion générale 63 avancées, à la programmation informatique et aux méthodes vibratoires de modélisation, de détection et de localisation des endommagements. Nous proposons comme perspective, la réalisation d’études similaires sur des géométries plus complexes afin d’enrichir le programme développé et de généraliser l’algorithme de détection des endommagements pour le cas de structures bi et tridimensionnelles.Item Détection des défauts et maintenance des groupes électrogènes(Université Mouloud Mammeri, 2023) Aouakli Said; Messaoudi DyhiaLa détection des défauts dans les groupes électrogènes est essentielle pour maintenir leur fonctionnement efficace et prévenir les dysfonctionnements. Les défauts les plus courants comprennent les pannes du système de carburant, les dysfonctionnements du système de refroidissement, les fuites de carburant ou d'huile et les problèmes électriques. La détection des défauts peut être effectuée en utilisant des méthodes telles que l'analyse de l'huile, les inspections visuelles, les tests de tension et les analyses thermographiques. Les programmes de maintenance préventive peuvent également être utilisés pour détecter les défauts potentiels avant qu'ils ne deviennent un problème. Il est important d'effectuer des inspections régulières des groupes électrogènes pour détecter les défauts et résoudre les problèmes avant qu'ils ne causent des pannes coûteuses. Les professionnels de l'entretien doivent être formés pour détecter les défaillances potentielles et effectuer des réparations en temps opportun pour éviter des temps d'arrêt coûteux. En fin de compte, la détection des défauts dans les groupes électrogènes est essentielle pour garantir leur fonctionnement efficace et fiable. Les inspections régulières, les tests et les programmes de maintenance préventive sont des outils importants pour détecter les défauts et prévenir les pannes.